Made of heavy wall plate glass, with fired edges.

For handling or manipulating hot crucibles and similar apparatus. Corrugated tips for easy handling. Riveted joint. Finger openings are large enough for firm grip. Overall length about 200mm.

For tubes from 10mm to 19mm diameter. With a steel spring. Jaws open by thumb pressure. Smooth finish. Length about 180mm.

Consists of a flat circular cast iron plate with integral bosshead and plated thumbscrew. Inside diameter of the rim 127mm (5in). Can be clamped to rods up to 16mm diameter.

For holding flat object upright. Cast iron, enamelled base with steel thumbscrew. Distance between the jaws is 3.4cm and the height of the jaw is 4cm. Dimensions: (l x w), 9.5 x 7.5cm.

For supporting various sizes of crucibles, and apparatus. Consists of a circular tripod stand with two removable concentric rings. The plated steel legs are detachable and sloped outwards for stability. Outer diameter of the ring is 150mm (6in) and overall height is 220mm (8 5/8in). Black enamel finish. Shipped unassembled.

Triangular shape top with each side approximately 125mm (5in) and detachable legs sloped outwards for stability. Overall height is approximately 220mm (8 5/8in). Made of plated steel.

For providing a firm grip on objects of diameter from 2mm to 90mm. Four pronged clamp of cast alloy with brass thumbscrew and cork lined jaws. Overall length approximately 240mm.

For ensuring a firm grip on small round or irregularly shaped objects. Three pronged aluminum die-cast clamp with brass thumbscrew. Jaws are covered with replaceable rubber tube, which open from 3-90mm. Overall length approximately 250mm .

For connecting two rods at right angles forming L or T shape. Made of die-cast alloy with plated brass thumbscrews. It can accept or be clamped to rods up to 18mm diameter.

For obtaining broad, fishtail flame that heats large area and smoothly bends glass. Also useful for flame tests and paint stripping. Made of brass. Fits over a range of burner mixing tubes.

For double buret. This is an all metal clamp to hold 2 burets. Easy clamping support on support stand rod up to 18mm

Suitable for test tubes of diameter 9-13mm, 13-19mm, 19-25mm respectively. Nylon bristles, fan shaped at one end on a twisted galvanised iron wire.

For vacuum filtration and other low vacuum laboratory applications. With 9mm serrated inlet nozzles. Designed to prevent flooding and turbulence.

For sharpening hollow cork borers from 5 to 22mm in diameter. Consists of a brass cone to fit the borer, with a hinged steel blade ground to sharpen the cutting end of the borer. Mounted in a wooden handle. Total length, 190mm.

For use at temperatures up to 800°C. Glazed inside and outside except for outside bottom surface. With lid.

Substitute for porcelain tiles. Made of strong, white, unbreakable plastic and has 12 depressions. Washable.

For staining microscope slides with dyes or chemicals. Has five grooves to hold 10 standard (l x w), 75 x 25mm slides back to back in erect position. With domed threaded screw cap. Approximately 114mm high.

Single piece, molded of translucent plastic, with raised numerical graduations. Resistant to most common acids, bases and solvents. Has a broad base for stability. All sizes have pouring spouts. Does not have meniscus. Autoclavable to 130 Degrees C.

Raised graduations in liters and milliliters. Flat stable base. Translucent.

For conveniently pouring liquids in containers. Translucent.

Made of galvanised woven wire with edges carefully turned over.

Made of plated sharpened brass tubing with attached handles including a steel punch. Diameters of the holes made, start with 5mm increasing as shown in the following data table.

For tapering, softening for boring and reducing corks upto 30mm diameter for exact fit. Made of cast iron. Rotary form. Mounted on wooden base.

All metal, leak proof alcohol burner. Permanent double wick for extra heating, no replacements needed. Tank capacity 100mL

For obtaining a very hot flame, suitable for glass work and soldering. Consists of a plated brass tube (h x o.d.), 105 x 13mm with threaded disc valve for adjustment of the air/gas mixture. Conical mixing section. Base diameter about 80mm and overall height 120mm. Serrated inlet tube diameter 9mm. Suitable for propane gas.

Angular shape allows it to be used while tilted. Glass with brass cap

A 20 tube rack for tubes up to 19mm in diameter. Three tier design measures (l x w x h), 325 x 125 x 70mm. The lower plate has rounded wells with drain holes. Convenient hand grips on both sides.

A 12 place rack for tubes up to 25mm in diameter. Three tier design measures (l x w x h), 225 x 125 x 70mm. The lower plate has rounded wells with drain holes. Convenient hand grips on both sides.

Replacement for wood and metal racks. For six test tubes. Has six openings of 25mm diameter on top plate, with hemispherical wells and drying pins. Open side for clear viewing. Can be easily assembled. Dimensions: (l x w x h), 240 x 70 x 90mm.

For clamping two apparatuses together or securing an apparatus to a table top. Also, useful for setting up rod mounted pulleys. Cast Iron enameled frame. Plated screw and vise type nut.

Suitable for student use. Made of molded soda glass with tightly fitting sealed brass cap. Alcohol is poured by removing threaded brass wick holder. Equipped with a glass cap for extinguishing the flame and to prevent evaporation of alcohol. Capacity about 125mL.

Made of kiln dried wood. Has six openings of 24mm diameter and six drying pins. Measures (l x w x h), 240 x 70 x 90mm. Oil finished.

Glass tubing cutter also known as glass tubing knife.

Permanent wick, no replacements needed. Tank capacity 100ml suffiecient for 1 1/2 hours use.

A heavy base with brass mixing pipe 13mm diameter and a 9mm diameter serrated gas inlet tube.

Has twelve openings of 20mm diameter. Measures (l x w x h), 200 x 140 x 70mm. Made of kiln dried wood. Oil finished.